| Parte No | Fabricante | Aplicación |
|---|
| ICL7614DCPA | MaximIC | "Single operational amplifier, 15mV" |
| MAX323EJA | MaximIC | "Precision, single-supply, SPST analog switch." |
| MX7541KN | MaximIC | CMOS 12 bit multiplying D/A converter. Error 1/2 LSB. |
| OP37CJ | MaximIC | Low-noise precision operational amplifier. 63MHz gain-bandwidth product. 17V/micros slew rate. |
| MAX804SMJA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.925V. Active-high reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX388CPN | MaximIC | "High-voltage, fault-protected analog multiplexer. 8-channel single-ended." |
| MAX6318LHUK44AX-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.390V min, reset timeout 1ms,typ watchdog timeout 102ms" |
| MX7543KN | MaximIC | CMOS serial input 12 bit DAC. Error +1/2 LSB. |
| MAX634MJA | MaximIC | CMOS micropower inverting switching regulator |
| MXD1000UA40 | MaximIC | 5-tap silicon delay line |
| MAX6316LUK26DX-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.630V, min reset timeout 1120ms, typ watchdog timeout 102ms" |
| MAX130EQH | MaximIC | 3 1/2 Digit A/D converter with bandgap reference |
| MAX4103ESA | MaximIC | "180MHz -3dB bandwidth, broadcast-quality, low-power video op amp." |
| MAX6350CSA | MaximIC | "Low-noise, +5V voltage reference. Max tempco 1.0ppm/C" |
| MAX6321HPUK43DX-T | MaximIC | "Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.300V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms" |
| MAX4074BEEUK-T | MaximIC | "Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 24V/V, noniverting gain 25V/V, -3dB BW 120kHZ." |
| MAX1245BCPP | MaximIC | "+2.375V, low-power, 8-channel, serial 12-bit ADC ." |
| MAX786SCAI | MaximIC | Dual-output power-supply controller for notebook computers |
| MAX6313UK45D4-T | MaximIC | "Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 4.388(min) 4.613(max).Nominal timeout period 1120ms |
| MAX538BEPA | MaximIC | "+5V, low-power, voltage-output, serial 12-bit DAC. Error (LSB) +-1. 140microA supply current. Flexible output range 0V to 2.6V." |
| MAX4542CSA | MaximIC | "Low-voltage, single-supply dual SPST analog switch." |
| MAX5003CSE | MaximIC | High-voltage PWM power-supply controller. |
| MX565ASQ | MaximIC | High speed 12-bit monolithic D/A converter. High stability buried zener 10V reference. Error +-1/2LSB |
| MAX6318MHUK45CX-T | MaximIC | "Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms" |
| MAX6502UKP055-T | MaximIC | "Low-cost, +2.7V to +5.5V micropower temperature switch. Output stage push-pull. Standard temperature threshold(C) +55." |
| MAX6318LHUK39BY-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.900V min, reset timeout 20ms,typ watchdog timeout 1.6sec" |
| MAX746C/D | MaximIC | "High-efficiency, PWM, step-down, N-channel DC-DC controller" |
| MAX709TC/D | MaximIC | Power-supply monitor with reset. Reset threshold voltage 3.08V |
| MAX165BCWN | MaximIC | "CMOS microprocessor-compatible, 5 microsec, 8-bit ADC. Error +-1 LSB. Plug-in upgrade to the MX7575." |
| MAX8875EUK25-T | MaximIC | "Low-dropout, 150mA linear regulator with power-OK output. Preset output voltage 2.5V." |
