| Parte No | Fabricante | Aplicación |
|---|
| MAX9001EUB | MAXIMIC | Low-power, high-speed, single-supply op amp + comparator + reference IC. Internal precision reference 1.23V. Op-Amp gain stability 1V/V. Op-Amp gain bandwidth 1.25MHz. Shutdown mode. |
| MAX883MJA | MAXIMIC | 5V or adjustable, low-dropout, low current, 200mA linear regulator. 1microA(max) shutdown(OFF) mode. |
| MAX761EPA | MAXIMIC | 12V or adjustable, high-efficiency, low Iq, step-up DC-DC converter. |
| MAX3225EEAP | MAXIMIC | +-15kV ESD-protected, 1microA, 1Mbps, 3.0V to 5.5V, RS-232 transceiver with autoshutdown plus. |
| MAX232EESE | MAXIMIC | +-15kV ESD-protected, +5V RS-232 transceiver |
| MAX1249AEPE | MAXIMIC | +2.7V to 5.25V, low-power, 4-channel, serial 10-bit ADC. INL (LSB) +1/2,-1/2 |
| MAX4052CEE | MAXIMIC | Low-voltage, CMOS analog multiplexer |
| MAX6319LHUK38B-T | MAXIMIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 3.800V, reset timeout(min) 20ms |
| MAX6103EUR-T | MAXIMIC | Low-cost, micropower, low-dropout, high-output-current, SOT23 voltage reference. Output voltage 3.000V, input voltage range (Vout + 200mV)V to 12.6V to 12.6V. |
| MAX464ENI | MAXIMIC | Two-channel, quad RGB switch and buffer. Voltage gain 1V/V. |
| MAX154BCNG | MAXIMIC | CMOS high-speed 8-bit ADC with multiplexer and reference. Error (LSB) +,-1 |
| MAX3087CSA | MAXIMIC | Fail-safe, high-speed (10Mbps), slew-rate-limited RS-485/RS-422 transceiver |
| MAX780AC/D | MAXIMIC | Dual-slot PCMCIA analog power controller. Reference & Vpp status indicator. Register for direct connection to CPU data bus. Dual Vpp switches & level shifter for Vcc switching. |
| MAX802TCSA | MAXIMIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 3.075V. Active-low reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX665C/D | MAXIMIC | 8V CMOS switched-capacitor voltage converter. |
| MAX5160NEUA | MAXIMIC | Low-power, digital potentiometer. R(kom) 200. |
| MAX509ACAP | MAXIMIC | Quad, serial 8-bit DAS with Rail-to-Rail output. TUE (LSB) +-1 |
| MAX4615CPD | MAXIMIC | Low-woltage, high-speed, quad, SPST, CMOS analog switch has four NC switches. |
| MAX632ACPA | MAXIMIC | CMOS fixed +12V output voltage, adjustable output with 2 resistors step-up switching regulator. 5% output accuracy. |
| MAX905CPD | MAXIMIC | Single, high-speed, positive edge-triggered, ECL-compatioble voltage comparator. |
| MAX6318MHUK44CZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX4075ABESA | MAXIMIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 0.25V/V, noninverting gain 1.25V/V, -3dB BW 200kHz. |
| MAX6318MHUK50DX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms |
| MAX906CSE | MAXIMIC | Dual, high-speed, positive edge-triggered, ECL-compatioble voltage comparator. |
| MAX6320PUK44CY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec |
| MXL1007CS | MAXIMIC | Low-noise, precision operational amplifier. |
| OP37GS | MAXIMIC | Low-noise precision operational amplifier. 63MHz gain-bandwidth product. 17V/micros slew rate. |
| MAX1603EAI | MAXIMIC | Dual-channel CardBus and PCMCIA VCC/VPP power-switching netwok |
| MAX4374FEUB | MAXIMIC | Low-cost, micropower, high-side current-sense amplifier + comparator + reference IC. Gain +50V/V. |
| MAX6317HUK45BY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.500V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
