| Parte No | Fabricante | Aplicación |
|---|
| MAX5461EXT | MaximIC | 2-wire digital potentiometer, 100KOm |
| MAX495CUA | MaximIC | Single, micropower, single-supply operation (+2.7V to +6V), Rail-to-Rail op amp. |
| MAX1249ACPE | MaximIC | +2.7V to 5.25V, low-power, 4-channel, serial 10-bit ADC. INL (LSB) +1/2,-1/2 |
| MAX697MJE | MaximIC | Microprocessor supervisory circuit. Onboard gating of chip enable signals. |
| MAX763ACPA | MaximIC | Step-down, current-mode PWM DC-DC controller. Input voltage range 3.3V to 11V |
| MAX6356MRUT-T | MaximIC | Triple-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.38V (Vcc5) and 2.63V (Vcc3). Active-low push-pull reset 5V. |
| MAX6318LHUK43CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.300V min, reset timeout 140ms,typ watchdog timeout 25.6sec |
| MAX4603EAE | MaximIC | Low on-resistance (2.5om max), quad, SPST, CMOS analog switches (two NO and two NC switches). |
| MAX3084CPA | MaximIC | Fail-safe, high-speed (10Mbps), slew-rate-limited RS-485/RS-422 transceiver |
| MAX130EPL | MaximIC | 3 1/2 Digit A/D converter with bandgap reference |
| MAX139CMH | MaximIC | 3 1/2 digit A/D converter with bandgap reference and charge-pump voltage converter |
| MAX6312UK27D2-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 2.633(min) 2.768(max). Nominal timeout period 20ms. |
| MAX274BMRG | MaximIC | 8th-order continuous-time active filter |
| MAX6321HPUK50AW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| MAX4560CSE | MaximIC | +-15kV ESD-protected, low-voltage, CMOS analog switch (triple SPDT). |
| MAX339ESE | MaximIC | Dual 4-channel, low-leakage, CMOS analog multiplexer. |
| MAX428CSA | MaximIC | Dual high-speed, fast-settling, high output current operational amplifier |
| MAX6320PUK26CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| MAX6316MUK39AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.900V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX4274ANESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 8, 1+ (Rf/Dg) noninverting gain 9, -3dB BW 480kHz. |
| MAX6318MHUK44CY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec |
| MAX212C/D | MaximIC | +3V-powered, low-power, true RS-232 tranceiver. |
| MAX4622EPE | MaximIC | Low on-resistance 3om(typ), 5om(max), dual, SPDT, analog switch has two NO and two NC poles. |
| MAX400CPA | MaximIC | Ultra low offset voltage operational amplifier. |
| MAX518AEPA | MaximIC | 2-wire serial 8-bit dual DAC with Rail-to-Rail outputs. TUE(LSB) 1. |
| MAX675ESA | MaximIC | +5V precision voltage reference. Temp. coefficient 15ppm/degC, Initial error 7mV. |
| MAX6316MUK38DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.800V, min reset timeout 1120ms, typ watchdog timeout 25.6sec |
| IH5050CPE | MaximIC | CMOS analog switch. |
| MAX280CWE | MaximIC | 5th order, zero DC error, lowpass filter. |
| MAX6316MUK26AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 2.630V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
