| Parte No | Fabricante | Aplicación |
|---|
| MXD1013PD030 | MaximIC | 3-in-1 silicon delay line. Output delay 30ns. |
| MAX636BC/D | MaximIC | Preset -12V output or adjuistable output with 2 resistors, CMOS switching regulator. Output accuracy 10%. |
| MAX4573CEI | MaximIC | Serially controlled, clickless audio/video switch. 3-wire, SPI/QSPI/MICROWIRE - compatible. |
| MAX417CSA | MaximIC | 1.2microA max, dual, single-supply op amp. |
| MAX6320PUK36CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| HI1-0508A-2 | MaximIC | Fault-protected analog 8 channel single-ended (1 of 8) multiplexer. |
| MAX110ACWE | MaximIC | Low-cost, 2-channel, 14-bit serial ADC |
| MAX746CSE | MaximIC | High-efficiency, PWM, step-down, N-channel DC-DC controller |
| MAX6317HUK30BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.000V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX4669ESE | MaximIC | 2.5om, quad, SPST, CMOS analog switch (one NC and one NO switches). |
| MAX502ACNG | MaximIC | Voltage-output, 12-bit multiplying DAC. Error(LSBs) +-1/2. |
| MAX317ESA | MaximIC | Precision, CMOS analog switch |
| MX7537JCWG | MaximIC | CMOS parallel loading dual 12 bit multiplying D/A converter. Gain error +-6 LSB. |
| MAX820LEJE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 4.62V. Reset and low-line threshold accuracy +-2% |
| MAX243MJE | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX4175BGEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 30, 1+ (Rf/Dg) noninverting gain 31, -3dB BW 510kHz. |
| MAX6318MHUK33BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.300V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX840ISA | MaximIC | Low-noise, regulated, -2V GaAsFET bias. Fixed -2V or adjustable -0.5V to -9.4V output at 4mA. 1microA max logic-level shutdown over temp. |
| MAX318ESA | MaximIC | Precision, CMOS analog switch |
| MAX690AMJA | MaximIC | Microprocessor supervisory circuit. 4.65V precision supply-voltage monitor |
| MAX6337US20D2-T | MaximIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, open-drain) . Reset threshold(typ) 2.0V, reset timeout(min) 20ms. |
| MAX6316LUK31AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX663EPA | MaximIC | Dual Mode 5V or programmable micropower voltage positive regulator. |
| MAX6328XR24-T | MaximIC | Ultra-low-power microprocessor supervisory circuit (reset output active-low, open-drain). Reset threshold (typ) 2.400V. Order increment 10k |
| MAX4519ESD | MaximIC | Precision, dual 2-channel, low-voltage, CMOS analog multiplexer. Single-supply operation (+2.2V to +15V) or bipolar-supply operation (+-2.2V to +-8V). |
| MAX6317HUK32BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.200V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX6333UR18D1-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 1.8V, reset timeout(min) 1ms. |
| MAX3220TCAP | MaximIC | 3V to 5.5V, up to 250kbps true RS-232 transceiver with 4microA autoshutdown plus and power-on reset. Reset threshold 3.08V. |
| MAX730AESA | MaximIC | 5V, step-down, current-mode PWM DC-DC converter accept input between 5.5V and 11V and deliver 450mA for inputs above 6V. |
| MAX3186CWP | MaximIC | +-15kV ESD-protected, EMC-compliant, 230kbps RS-232 serial port for modems. |
