| Parte No | Fabricante | Aplicación |
|---|
| MAX6318LHUK31BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.080V min, reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX6319MHUK48C-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.800V, reset timeout(min) 140ms |
| MAX1487ECPA | MaximIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 230 microA. Number of transmitter on bus - 128. |
| MAX485ECPA | MaximIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX4074CAESA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 100V/V, noninverting gain 101V/V, -3dB BW 38kHZ. |
| MAX6314US27D2-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 2.70V. Reset timeout period(min) 20ms. |
| MAX6321HPUK49BW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 20ms, watchdog timeout(typ) 6.3ms |
| MAX6317HUK42AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.200V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| MAX6320PUK38BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.800V, reset timeout(min) 20ms, watchdog timeout(typ) 102ms |
| MAX6316LUK31CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX4372FESA | MaximIC | Low-cost, micropower, high-side current-sense amplifier with voltage output. +50V/V gain. |
| MAX6319MHUK41C-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 140ms |
| MAX4573EEI | MaximIC | Serially controlled, clickless audio/video switch. 3-wire, SPI/QSPI/MICROWIRE - compatible. |
| MAX6318MHUK27BW-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 20ms, watchdog timeout(typ) 6.3ms |
| MAX809SEUR-T10 | MaximIC | Microprocessor reset circuit. Reset threshold 2.93V. Push-pull active-high reset. 10k increments. |
| MAX6314US34D1-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 3.40V. Reset timeout period(min) 1ms. |
| MAX6318LHUK45BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.500V min, reset timeout 20ms,typ watchdog timeout 1.6sec |
| MAX6317HUK28BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX622EPA | MaximIC | High-side power supply. |
| MAX4517ESA | MaximIC | +-1V to +-6V dual-supply opration, low-on-resistance, SPST, CMOS analog switch. Normally closed (NC). |
| MAX202CSE | MaximIC | +5V RS-232 transceiver with 0.1 microF external capacitors |
| MX7837C/D | MaximIC | Complete, dual, 12-bit multiplying DAC. 8-bit + 4-bit interface. Error (LSB) +-1 |
| IH5145C/D | MaximIC | Low power fast CMOS analog switch. Dual, double pole, single throw (Dual DPST). |
| MAX932CUA | MaximIC | Dual low-power, low-cost comparator with intarnal 1.182V+-2% bandgap reference and internal programmable hysteresis.. |
| MX7837BQ | MaximIC | Complete, dual, 12-bit multiplying DAC. 8-bit + 4-bit interface. Error (LSB) +-1/2 |
| MAX483C/D | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| MAX4175AKEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 4, 1+ (Rf/Dg) noninverting gain 5, -3dB BW 970kHz. |
| MAX189ACWE | MaximIC | +5V, low-power, 12-bit serial ADC. Error(LSB) +-1/2. |
| MAX496CSE | MaximIC | 375MHz -3dB bandwidth, quad closed-loop video buffer, fixed gain +1V/V, 1600V/micros slew rate. |
| MAX281ACWE | MaximIC | 5th-order, zero-error, bessel lowpass filter. |
