| Parte No | Fabricante | Aplicación |
|---|
| MAX506BEWP | MaximIC | Quad 8-bit DAC with Rail-to-Rail voltage outputs. Separate input latches for each of its four DACs. TUE +-3/2 LSB. |
| MAX6194CESA | MaximIC | Precision, micropower, low-dropout voltage reference. Output voltage 4.500V, initial accuracy +-10, temperature coefficient <25ppm. |
| ICM7212IQ | MaximIC | Four digit display decoder/driver. LED, output code - hexadecimal, input configuration - multiplexed 4-bit. |
| MAX6321HPUK28DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.800V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX126ACAX | MaximIC | 2x4-channel, simultaneous-sampling 14-bit DAS. INL (LSB) +2,-2 |
| MAX6318MHUK34DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.400V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX412BEPA | MaximIC | Dual, 28MHz, low-noise, low-voltage, precision op amp. |
| MAX4529CUT-T | MaximIC | Low-voltage, bidirectional RF and video switch. |
| MAX6318MHUK39AX-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 1ms, watchdog timeout(typ) 102ms |
| MAX6808XR46-T | MaximIC | Voltage detector. Reset output active-low, open-drain. Threshold reset 4.6V |
| MAX4621CSE | MaximIC | Low on-resistance 3om(typ), 5om(max), dual, SPST, NO analog switch. |
| ICM7260IPE | MaximIC | Programmable timer/counter |
| REF02DP | MaximIC | +5V precisioon voltage reference. Max TEMPCO 250ppm/degC. Initial error +-100mV |
| MX7538JP | MaximIC | Microprocessor compatible CMOS, 14-bit D/A converter. Error +-2 LSB. |
| MAX267BCNG | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 2%. |
| MAX806SESA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.925V. Active-low reset. Manual reset input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX755C/D | MaximIC | Negative output, inverting, current-mode PWM regulator. Converts +2.7V to +9V input to adjustable negative output. |
| MAX6322HPUK42D-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.200V, reset timeout(min) 1120ms |
| MAX396C/D | MaximIC | Precision, 16-channel, low-voltage, CMOS analo0g multiplexer. |
| MAX1406CAE | MaximIC | +-15V, ESD-protected, EMC-compliant, 230kbps, 3-Tx/3-Rx RS-232 IC. |
| MAX4602CWE | MaximIC | Low on-resistance (2.5om max), quad, SPST, CMOS analog switches (four NO switches). |
| MAX8867EUK28-T | MaximIC | Low-noise, low-dropout, 150mA linear regulator. Preset output voltage 2.80V |
| MAX4565EAP | MaximIC | Quad, low-voltage, bidirectional RF/video switch. |
| MAX560CAI | MaximIC | +3.3V tranceiver with two EIA/TIA-562 receivers active in shutdown. |
| MAX5155BEEE | MaximIC | Low-power, dual, 12-bit voltage-output DAC with serial interface. +3V single-supply operation. INL(LSB) +-2. |
| MAX6318MHUK49AW-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| ICL7611ACTV | MaximIC | Single operational amplifier, 2mV |
| MAX6250ACSA | MaximIC | Low-noise, precision, +5V output voltage reference. Max TEMPCO (ppm/C) 2.0. |
| MAX243CPE | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MX7541AAQ | MaximIC | CMOS 12 bit multiplying D/A converter. Error 1 LSB. |
