| Parte No | Fabricante | Aplicación |
|---|
| MAX3264C/D | MaximIC | 3.0V to 5.5V, 1.25Gbps limiting amplifier. |
| MAX267AMRG | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 1%. |
| MAX421MJD | MaximIC | +-15V chopper stabilized operational amplifier. |
| MAX6318LHUK40CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.000V min, reset timeout 140ms,typ watchdog timeout 1.6sec |
| MF10BN | MaximIC | Dual universal switched capacitor filter. |
| MAX941EPA | MaximIC | Single, high-speed, low-power, 3V or 5V single-supply, Rail-to-Rail comparator |
| MAX6316MUK32AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.200V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| MAX2450CEP | MaximIC | 3V, ultra-low-power quadrature modulator/demodulator. |
| MAX6316MUK43CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.300V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX870EUK/D | MaximIC | Switched-capacitor voltage inverter. Input voltage range +1.4V to +5.5V. 0.7mA quiescent current. 125kHz |
| MAX5468EUT | MaximIC | 2-wire digital potentiometer, 10KOm |
| MAX706SCPA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 2.93V. Active-low reset output signal. |
| MAX393C/D | MaximIC | Precision, quad, SPST analog switch |
| MX7541AKN | MaximIC | CMOS 12 bit multiplying D/A converter. Error 1/2 LSB. |
| MAX860ISA | MaximIC | 50mA, Frequency-selectable, switched-capacitor voltage coverter. Input voltage +1.5V to 5.5V, 200microA quiescent current. |
| MAX953EUA | MaximIC | Ultra low-power, single-supply Op Amp + comparator. Op Amp gain stability 1V/V. Supply current 5microA. |
| MAX4531EAP | MaximIC | Low-voltage, CMOS analog ICs configured as two 4-channel multiplexer. |
| MAX942ESA | MaximIC | Dual, high-speed, low-power, 3V or 5V single-supply, Rail-to-Rail comparator |
| MAX8867EUK33-T | MaximIC | Low-noise, low-dropout, 150mA linear regulator. Preset output voltage 3.30V |
| MAX905MJD | MaximIC | Single, high-speed, positive edge-triggered, ECL-compatioble voltage comparator. |
| MAX6316LUK32AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.2000V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX6306UK32D3-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 3.120(min),3.280(max) Nominal timeout period 140ms. |
| DG528DN | MaximIC | 8-channel latchable multiplexer |
| MAX1771EPA | MaximIC | 12V or adjustable, high efficiency, low current, step-up DC-DC controller. |
| MAX4503C/D | MaximIC | Low-voltage, dual-supply, SPST, CMOS analog switch. |
| MAX4126ESA | MaximIC | Dual, wide-bandwidth, low-power, single-supply Rail-to-Rail I/O op amp. BW 5MHz. |
| MAX814NEPA | MaximIC | +-1% accuracy, low-power, microprocessor supervisory circuit. Reset trip threshold (min) 4.50V (max) 4.60V, push-pull active-low reset output, push-pull active-high reset output, manual reset, power-fail monitor, low-line detector. |
| MAX191BMRG | MaximIC | Low-power, 12-bit sampling ADC with internal reference and power-down. Error(LSB) +-1. |
| MAX4253ESD | MaximIC | Dual, single-supply operation +2.4V to 5.5V, low-noise, low-distortion, Rail-to-Rail op amp. Gain bandwidth 3MHz, min stable gain 1V/V. |
| MAX1482EPD | MaximIC | 20 micro A, 1/8-unit-load, slew-rate-limited RS-485 transceiver |
