| Parte No | Fabricante | Aplicación |
|---|
| MAX819LCUA | MaximIC | +5V microprocessor supervisory circuit. Reset threshold 4.65V, active-low reset, backup-battery switchover, power-fail comparator, battery freshness seal, manual reset input. |
| MAX6319MHUK25A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 1ms |
| MAX4511MJE | MaximIC | Quad, Rail-to-Rail, fault-protected, SPST analog switch. |
| MAX196ACWI | MaximIC | Multirange, single +5V, 12-bit DAS with 12-bit bus interface |
| MAX6314US49D3-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 4.90V. Reset timeout period(min) 140ms. |
| DG381CK | MaximIC | General purpose CMOS dual analog switch. |
| MAX6309UK50D4-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 4.875(min),5.125(max) Nominal timeout period 1120ms. |
| MAX6346XR44-T | MaximIC | Microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 4.380V. Standard version. Order increment 2.5k |
| MX7523KN | MaximIC | CMOS 8 bit multiplying D/A converter. Error 1/4LSB |
| MAX6313UK28D3-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 2.730(min) 2.870(max).Nominal timeout period 140ms. |
| MAX220MJE | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX767SCAP | MaximIC | 5V-to-3.3V, Synchronous, step-down power-supply controller. Ref.tol.+-1.8%, Vout 3.6V |
| OP07ECSA | MaximIC | Low offset voltage operational amplifier. |
| MAX708RMJA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 2.63V. Active-low and active-high reset output signal. |
| MAX6316LUK38CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.800V, min reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX4504CUK | MaximIC | Low-voltage, dual-supply, SPST, CMOS analog switch. |
| MAX454MJD | MaximIC | CMOS 50MHz video amplifier with an on-board multiplexer offering 4-channels |
| MAX261ACNG | MaximIC | Microprocessor programmable universal active filter. Accuracy 1%. |
| MAX6320PUK39BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX265BCWI | MaximIC | Pin and resistor programmed universal active filter. Accyracy 2% |
| MAX6318MHUK44AW-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| MAX708TEPA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 3.08V. Active-low and active-high reset output signal. |
| MAX6312UK36D3-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 3.510(min) 3.690(max). Nominal timeout period 140ms. |
| MAX5251ACAP | MaximIC | +3V, quad, 10-bit, voltage-output DAC with serial interface. INL(LSB) +-1/2. |
| MAX6318MHUK27BY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX6318LHUK28CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.800V min, reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX4508C/D | MaximIC | Fault-protected, high-voltage single 8-to-1 multiplexer. |
| MX7821KP | MaximIC | 660ns microprocessor-compatible, 8-bit ADC with track/hold. |
| MAX6322HPUK33C-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.300V, reset timeout(min) 140ms |
| MAX6314US35D3-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 3.50V. Reset timeout period(min) 140ms. |
