| Parte No | Fabricante | Aplicación |
|---|
| DG507ACWI | MaximIC | Monolithic CMOS differential 8 channel (2 of 16) analog multiplexer. |
| MAX6322HPUK32C-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.200V, reset timeout(min) 140ms |
| MAX505BCNG | MaximIC | Quad 8-bit DAC with Rail-to-Rail voltage outputs. Double-buffered logic inputs. TUE +-3/2 LSB. |
| HI3-0201-5 | MaximIC | Quad SPST CMOS analog switch |
| MAX4274AHEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 2.5, 1+ (Rf/Dg) noninverting gain 3.5, -3dB BW 820kHz. |
| MAX6316MUK31DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 1.12sec, typ watchdog timeout 6.3ms |
| MAX6316MUK26BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 2.630V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX5464EXT | MaximIC | 2-wire digital potentiometer, 50KOm |
| MX674AUD | MaximIC | Industry standard complete 12-bit A/D converter. 15 microsec. max conversion time. Linearity (LSBs) 3/4. TEMPCO(ppm/C) 12. |
| MAX6318LHUK25BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.500V min, reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX4538C/D | MaximIC | Quad, low-voltage, SPST analog switches with enable. 2 NO and 2 NC. |
| DG509ADY | MaximIC | Monolithic CMOS analog multiplexer. Differential 4-channel (2-of-8). |
| MAX512MJD | MaximIC | Low-cost, triple, 8-bit voltage-output DAC with serial interface. |
| MAX693EJE | MaximIC | Microprocessor supervisory circuit. |
| MAX787CCK | MaximIC | 5V 5A step-down, PWM, switch-mode DC-DC regulator. |
| MAX395CNG | MaximIC | Serially controlled, low-voltage, 8-channel SPST switch |
| MAX6316MUK29BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 2.930V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX4504MJA | MaximIC | Low-voltage, dual-supply, SPST, CMOS analog switch. |
| MAX6321HPUK50BY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX4510EUT-T | MaximIC | Rail-to-Rail, fault-protected, SPST analog switch. |
| MAX6318LHUK27DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.700V min, reset timeout 1.12sec, typ watchdog timeout 1.6sec |
| MX580JH | MaximIC | High precision +2.5V reference. Tolerance +-75mV |
| MXD1013UA070 | MaximIC | 3-in-1 silicon delay line. Output delay 70ns. |
| MAX6321HPUK27BX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 20ms, watchdog timeout(typ) 102ms |
| MAX815TCPA | MaximIC | +-1% accuracy, low-power, microprocessor supervisory circuit. Reset trip threshold (min) 3.00V (max) 3.06V, push-pull active-low reset output, manual reset, power-fail monitor, watchdog circuit. |
| MX7226K/D | MaximIC | CMOS quad 8-bit D/A converter with separate input registers. Error +-2 LSB. |
| MAX3093ECPE | MaximIC | +/-15kV ESD-protected, 10 Mbp, 3V/5V, low-power quad RS-422/RS-485 receiver |
| MAX358EPE | MaximIC | Fault-protected analog 8 channel single-ended (1 of 8) multiplexer. |
| MAX6320PUK38DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.800V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| DG301BA | MaximIC | Dual, TTL compatible CMOS analog switch. |
