| Parte No | Fabricante | Aplicación |
|---|
| MAX6309UK33D3-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 3.218(min),3.383(max) Nominal timeout period 140ms. |
| MAX4275BLESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 60, 1+ (Rf/Dg) noninverting gain 61, -3dB BW 310kHz. |
| MX584SQ | MaximIC | Pin programmable precision voltage reference. Error +-30mV. |
| ICL7106CJL | MaximIC | 3 1/2 digit a/d converter |
| MAX6327XR30-T | MaximIC | Ultra-low-power microprocessor supervisory circuit (reset output active-high, push-pull). Reset threshold (typ) 3.000V. Order increment 10k |
| MAX6318MHUK34CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.400V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX6314US46D2-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 4.63V. Reset timeout period(min) 20ms. |
| HI1-0509A-2 | MaximIC | Fault-protected analog 4 channel differential (2 of 8) multiplexer. |
| MAX192BCPP | MaximIC | Low-power, 8-channel, serial 10-bit ADC. Error(LSB) +-1. |
| IH5145CWE | MaximIC | Low power fast CMOS analog switch. Dual, double pole, single throw (Dual DPST). |
| MAX4274BMESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 80, 1+ (Rf/Dg) noninverting gain 81, -3dB BW 260kHz. |
| MAX6318LHUK49DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input, reset output active-low, push/pull; active-high,push/pull).Factory-trimmed reset threshold (typ) 4.900V, min reset timeout 1.12sec, typ watchdog timeout 1.6sec |
| MAX871EUK | MaximIC | Switched-capacitor voltage inverter. Input voltage range +1.4V to +5.5V. 500kHz |
| MAX1618MUB | MaximIC | Remote temperature sensor with SMBus serial interface |
| MX7547KEWG | MaximIC | CMOS parallel loading dual 12 bit multiplying D/A converter. Gain error +-3 LSB. |
| MAX6327UR27-T | MaximIC | Ultra-low-power microprocessor supervisory circuit (reset output active-high, push-pull). Reset threshold (typ) 2.700V. Order increment 10k |
| MAX6316LUK40BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX6337US23D3-T | MaximIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, open-drain) . Reset threshold(typ) 2.3V, reset timeout(min) 100ms. Standard version |
| MAX488EPA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - no. Receiver/driver enable - no. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| MAX550AEUA | MaximIC | +2.5V to +5.5V, low-power, single, 8-bit voltage-output DAC with an external reference input and an asynchronous load input. |
| MAX3227EAE | MaximIC | 1microA supply current, 1Mbps, 3.0V to 5.5V, RS-232 transceiver with autoshutdown plus |
| MXD1013PA200 | MaximIC | 3-in-1 silicon delay line. Output delay 200ns. |
| MAX620EWN | MaximIC | Quad, high-side MOSFET driver |
| MAX6318MHUK26CX-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX5152BC/D | MaximIC | Low-power, dual, 13-bit voltage-output DAC with configurable output amplifier. +5V single-supply operation. INL(LSB) +-1. |
| MAX6317HUK29AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 2.930V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MXD1005C/D250 | MaximIC | 5-tap silicon delay line |
| MAX6316LUK28BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX8862LESE | MaximIC | Low-cost, low-dropout, dual linear regulator. Fixed output voltage 4.95V |
| MAX8867C/D36 | MaximIC | Low-noise, low-dropout, 150mA linear regulator. Preset output voltage 3.60V |
