| Parte No | Fabricante | Aplicación |
|---|
| ICL7137CPL | MaximIC | Low power, 3-1/2 digit A/D converter |
| MAX1101CWG | MaximIC | Single-chip, 8-bit CCD digitizer with clamp and 6-bit PGA |
| MAX6316MUK28BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX792RCSE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 2.61V |
| MAX534ACPE | MaximIC | 5V, low-power, 8-bit quad DAC with Rail-to-Rail output buffer. INL (LSB) +-1 |
| MAX4274BMEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 80, 1+ (Rf/Dg) noninverting gain 81, -3dB BW 260kHz. |
| MAX6313UK48D1-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 4.680(min) 4.920(max).Nominal timeout period 1ms. |
| ICL7650CPA | MaximIC | Chopper-stabilized amplifier |
| MAX6313UK42D3-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 4.095(min) 4.305(max).Nominal timeout period 140ms. |
| MAX4175ACEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 0.5, 1+ (Rf/Dg) noninverting gain 1.5, -3dB BW 1280kHz. |
| MAX6314US48D3-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 4.80V. Reset timeout period(min) 140ms. |
| MAX161CEWI | MaximIC | CMOS 8-bit 8-channel data acquisition system. Error 1/2 LSB |
| MAX295CPA | MaximIC | 8th-order, lowpass, switched-capacitor filter. |
| MAX521AEPP | MaximIC | Octal, 2-wire serial 8-bit DAC with Rail-to-Rail, unbuffered outputs. TUE(LSB) 1. |
| MAX5480BCEE | MaximIC | 8-bit parallel DAC. Error(LSB) +-1. |
| MAX144ACUA | MaximIC | +2.7 V, low-power, 2-channel, 108 ksps, serial 12-bit ADC. INL(LSB) +-0.5 |
| MAX8216MJD | MaximIC | +-5V, +-15V dedicated microprocessor voltage monitor. |
| MAX6320PUK30CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX368CJN | MaximIC | Fault-protected analog multiplexer with latch. 8 channel single-ended (1 of 8). |
| MAX6348UR40-T | MaximIC | Microprocessor supervisory circuit (reset output active-low, open-drain). Reset threshold (typ) 4.000V. Order increment 10k |
| MAX414CPD | MaximIC | Quad, 28MHz, low-noise, low-voltage, precision op amp. |
| MX7574TQ | MaximIC | Microprocessor compatible 8-bit A/D converter. Fast conversion time 15microsec. Error +-1/2 LSB. |
| DG390BK | MaximIC | General purpose CMOS dual analog switch. |
| MX7226TQ | MaximIC | CMOS quad 8-bit D/A converter with separate input registers. Error +-2 LSB. |
| MAX819LESA | MaximIC | +5V microprocessor supervisory circuit. Reset threshold 4.65V, active-low reset, backup-battery switchover, power-fail comparator, battery freshness seal, manual reset input. |
| MX7534J/D | MaximIC | Microprocessor-compatible, 14-bit DAC. INL +-2 LSB. |
| MAX6321HPUK41DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX3485CPA | MaximIC | 3.3V-powered, 10Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 10Mbps. Supply voltage 3.0V to 3.6V |
| MAX6310UK41D3-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.998(min),4.203(max). Nominal timeout period 140ms. |
| MAX6313UK31D2-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 3.003(min) 3.157(max).Nominal timeout period 20ms. |
