| Parte No | Fabricante | Aplicación |
|---|
| MAX4175AFEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 1.5, 1+ (Rf/Dg) noninverting gain 2.5, -3dB BW 1180kHz. |
| MAX4612C/D | MaximIC | Low-voltage, quad, SPST, CMOS analog switches (two NC and two NO switches). |
| MAX706PEPA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 2.63V. Active-high reset output signal. |
| MAX6318MHUK35DW-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.500V, reset timeout(min) 1.12sec, watchdog timeout(typ) 6.3ms |
| MAX4541EAK-T | MaximIC | Low-voltage, single-supply dual SPST analog switch. |
| MX7543KN | MaximIC | CMOS serial input 12 bit DAC. Error +1/2 LSB. |
| MAX6320PUK49DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX6316MUK48DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 1120ms, typ watchdog timeout 6.3ms |
| MAX1248AEPE | MaximIC | +2.7V to 5.25V, low-power, 4-channel, serial 10-bit ADC. INL (LSB) +1/2,-1/2 |
| MAX6320PUK47BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.700V, reset timeout(min) 20ms, watchdog timeout(typ) 102ms |
| MAX6318MHUK32AW-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.200V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| MAX246EPL | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX932CSA | MaximIC | Dual low-power, low-cost comparator with intarnal 1.182V+-2% bandgap reference and internal programmable hysteresis.. |
| MAX6321HPUK38AX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.800V, reset timeout(min) 1ms, watchdog timeout(typ) 102ms |
| MAX6361HUT23-T | MaximIC | Low-power microprocessor supervisory circuit with manual reset input. Reset threshold(typ) 2.32V. Active-high push-pull reset. |
| MAX3095CPE | MaximIC | +-15kV ESD-Protected, 10Mbps, 3V quad RS-422/RS-485 receiver. |
| MAX824SEUK | MaximIC | Microprocessor supervisory circuit. Reset threshold 2.93V. Active-low reset. Active-high reset. Watchdog input. |
| MAX642BCSA | MaximIC | +12V fixed output, 10W CMOS step-up switching regulator. 10% output accuracy |
| MAX166CEPP | MaximIC | CMOS microprocessor-compatible, 5 microsec, 8-bit ADC. Error +-1/2 LSB. |
| MAX167ACNG | MaximIC | CMOS 12-bit A/D converter with track-and-hold. Error +-1/2 LSB. |
| MAX481ECSA | MaximIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX6312UK44D2-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 4.270(min) 4.490(max). Nominal timeout period 20ms. |
| MAX212EWG | MaximIC | +3V-powered, low-power, true RS-232 tranceiver. |
| MAX6320PUK26AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| ICL7650C/D | MaximIC | Chopper-stabilized amplifier |
| MAX6316MUK40CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX6342ZUT-T | MaximIC | Microprocessor reset circuit with power-fail comparator. Reset threshold 2.33V. Push-pull active-low reset output, manual-reset input. |
| MAX6320PUK32CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.200V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| MAX690TCSA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 3.075V. Active-low reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-4%. Power-fail comparator. Reset window +-75mV |
| ICL7612DC/D | MaximIC | Single operational amplifier, 15mV |
