| Parte No | Fabricante | Aplicación |
|---|
| MAX6347XR42-T | MaximIC | Microprocessor supervisory circuit (reset output active-high, push-pull). Reset threshold (typ) 4.200V. Order increment 10k |
| MAX155BEWI | MaximIC | 8-channel ADC with simultaneous T/Hs and reference. Error +-1 LSB. |
| MX7537TQ | MaximIC | CMOS parallel loading dual 12 bit multiplying D/A converter. Gain error +-3 LSB. |
| ICL7621BCPA | MaximIC | Dual operational amplifier, 5mV |
| MX7578KN | MaximIC | Calibrated 12-bit A/D converter |
| MAX6375UR30-T | MaximIC | Ultra-low-power voltage detector, 3.0V |
| ADC0820CCM | MaximIC | CMOS high speed 8-bit A/D converter with track/hold function. INL(LSB) +-1. |
| MAX628C/D | MaximIC | Dual power MOSFET driver contains one inverting and one non-inverting section. |
| MAX4173FESA | MaximIC | Low-cost,voltage-output, high-side current-sense amplifier. Gain 50V/V. |
| MAX4514EUK | MaximIC | Low-voltage, low-on-resistance, SPST, CMOS analog switch. Normally open (NO), +2V to +12V single-supply operation. |
| MAX4075AJESA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 3V/V, noninverting gain 4V/V, -3dB BW 90kHz. |
| MAX761C/D | MaximIC | 12V or adjustable, high-efficiency, low Iq, step-up DC-DC converter. |
| DG412DJ | MaximIC | Improved, quad, SPST analog switches |
| MAX861C/D | MaximIC | 50mA, Frequency-selectable, switched-capacitor voltage coverter. Input voltage +2.5V to 5.5V |
| MAX208ENG | MaximIC | +5V RS-232 transceiver with 0.1 microF external capacitors |
| MAX7401CPA | MaximIC | 8-th-order, lowpass, bessel, switched-capacitor filter. Single-supply operation +5V |
| MAX518BCPA | MaximIC | 2-wire serial 8-bit dual DAC with Rail-to-Rail outputs. TUE(LSB) 1.5. |
| MAX708TMJA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 3.08V. Active-low and active-high reset output signal. |
| MAX199ACWI | MaximIC | Multi-range (+-4V, +-2V, +4V, +2V), +5V supply, 12-bit DAS with 8+4 bus interface |
| MAX4455ECQ | MaximIC | Arbitrary graphics on-screen display video generator |
| MAX6316MUK33BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.300V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MXD1000SA45 | MaximIC | 5-tap silicon delay line |
| MAX139EQH | MaximIC | 3 1/2 digit A/D converter with bandgap reference and charge-pump voltage converter |
| MAX485CSA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX6320PUK50CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec |
| MAX6320PUK36AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX6309UK37D2-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 3.608(min),3.793(max) Nominal timeout period 20ms. |
| MAX709TESA | MaximIC | Power-supply monitor with reset. Reset threshold voltage 3.08V |
| ICM7212MIPL | MaximIC | Four digit display decoder/driver. LED, output code - hexadecimal, input configuration - micro P interface. |
| MAX349C/D | MaximIC | Serially controlled, low-voltage, 8-channel multiplexer |
