| Parte No | Fabricante | Aplicación |
|---|
| MAX264AMJI | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 1%. |
| MAX242MJN | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX6316MUK41CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.100V, min reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX6312UK48D4-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 4.680(min) 4.920(max). Nominal timeout period 1120ms. |
| MAX6380XR41-T | MaximIC | Ultra-low-power voltage detector, 4.1V |
| MAX6320PUK31BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.080V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX543BEWE | MaximIC | CMOS, 12-bit, serial-input multiplying DAC. Linearity (LSB) +-1 |
| MAX543AEPA | MaximIC | CMOS, 12-bit, serial-input multiplying DAC. Linearity (LSB) +-1/2 |
| MAX6313UK45D2-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 4.388(min) 4.613(max).Nominal timeout period 20ms. |
| MAX810ZEXR-T | MaximIC | Microprocessor reset circuit. Reset threshold 2.32V. Push-pull active-high reset. 2.5k increments. |
| IH5144MJE | MaximIC | Low power fast CMOS analog switch. Double pole, single throw (DPST). |
| MAX463CWG | MaximIC | Two-channel, triple RGB switch and buffer. Voltage gain 1V/V. |
| MAX8212CTY | MaximIC | Microprocessor voltage monitor with programmable voltage detection. High output current capability. |
| MAX480CSA | MaximIC | High-precision, low-voltage, micropower op amp. |
| MAX6313UK31D1-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 3.003(min) 3.157(max).Nominal timeout period 1ms. |
| MAX744ACPA | MaximIC | 5V, step-down, current-mode PWM DC-DC converter accept inputs between 65V and 16V and deliver 750mA. 159kHz to 212.5kHz guaranteed oscillator frequency limits. |
| MAX176BMJA | MaximIC | Serial-output, 250 ksps 12-bit ADC with T/H and reference. Error(LSB) +-1. |
| MAX6320PUK30CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| MAX6320PUK31DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.080V, reset timeout(min) 1.12sec, watchdog timeout(typ) 6.3ms |
| MAX6321HPUK41AX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 1ms, watchdog timeout(typ) 102ms |
| MAX622CPA | MaximIC | High-side power supply. |
| MAX6316LUK39AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.900V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX4166EUA | MaximIC | Single, high-output-drive, precision, low-power, single-supply +2.7V to +6.5V, Rail-to-Rail I/O op amp with shutdown. |
| MAX820MEPE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 4.37V. Reset and low-line threshold accuracy +-2% |
| MAX6316MUK30AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.000V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| DG506ACK | MaximIC | Monolithic CMOS single 16 channel (1 of 16) analog multiplexer. |
| MAX6318MHUK37BY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.700V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MX7530JD | MaximIC | CMOS 10 bit multiplying D/A converter. Error 0.2% |
| MAX1295BCEI | MaximIC | 265ksps, +3V, 6-channel single-ended/3-channel pseudo-differential, 12-bit ADC with +2.5V reference and parallel interface INL(LSB) +1, -1 |
| MAX6310UK46D4-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 4.514(min),4.746(max). Nominal timeout period 1120ms. |
