| Parte No | Fabricante | Aplicación |
|---|
| MAX6318LHUK45AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.500V min, reset timeout 1ms,typ watchdog timeout 102ms |
| MAX507BCWG | MaximIC | Voltage-output, 12-bit DAC with internal reference. 12 data-bus widths. Error +-3/4. |
| MAX4193EJA | MaximIC | CMOS micropower step-up switching regulator |
| MAX4667CPE | MaximIC | 2.5om, quad, SPST, CMOS analog switch (two NC switches). |
| MAX6332UR19D3-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 1.9V, reset timeout(min) 100ms. |
| MAX4531EWP | MaximIC | Low-voltage, CMOS analog ICs configured as two 4-channel multiplexer. |
| MAX4574EAI | MaximIC | Serially controlled, clickless audio/video switch. 3-wire, SPI/QSPI/MICROWIRE - compatible. |
| MAX320CUA | MaximIC | Precision, dual-supply, SPTS analog switch. |
| MX7672CQ05 | MaximIC | High-speed 12-bit A/D converter with external reference input. Fast conversion time 5 microsec. Linearity +-1/2 LSB. |
| MAX5353BCUA | MaximIC | Low-power, 12-bit voltage-output DAC with serial interface. INL (LSB) +-2. +3.3V single-supply operation. |
| MAX1481EUB | MaximIC | Software-selectable, half-/full-duplex, slew-rate-limite 12 Mbps, RS-485/RS-422 transceiver. |
| MAX6318MHUK41DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX636ACPA | MaximIC | Preset -12V output or adjuistable output with 2 resistors, CMOS switching regulator. Output accuracy 5%. |
| MAX6317HUK40BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX3081EPA | MaximIC | Fail-safe, high-speed (10Mbps), slew-rate-limited RS-485/RS-422 transceiver |
| MAX763AEPA | MaximIC | Step-down, current-mode PWM DC-DC controller. Input voltage range 3.3V to 11V |
| MAX6318LHUK47DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input, reset output active-low, push/pull; active-high,push/pull).Factory-trimmed reset threshold (typ) 4.700V, min reset timeout 1.12sec, typ watchdog timeout 25.6sec |
| MAX6302ESA | MaximIC | +5V, low-power microprocessor supervisory circuit with adjustable reset/watchdog (active-high reset, open-drain reset output). |
| MAX4513MJE | MaximIC | Quad, Rail-to-Rail, fault-protected, SPST analog switch. |
| MAX6195AESA | MaximIC | Precision, micropower, low-dropout voltage reference. Output voltage 5.000V, initial accuracy +-2, temperature coefficient <5ppm. |
| MAX622C/D | MaximIC | High-side power supply. |
| MAX6316LUK29AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.930V, min reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX6378UR38-T | MaximIC | Ultra-low-power voltage detector, 3.8V |
| MAX6711REXS-T10 | MaximIC | Microprocessor reset circuit with manual reset input. Reset threshold 2.63V. Output type active-low push-pull reset. |
| MAX4552C/D | MaximIC | +-15kV ESD-protected, quad, low-voltage, SPST analog switches (four NO switches). |
| MAX6310UK27D4-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 2.633(min),2.768(max). Nominal timeout period 1120ms. |
| MAX742CPP | MaximIC | Switch-mode regulator with +5V to +-12V or +-15V dual output. |
| MAX364ESE | MaximIC | Precision, quad, SPST, normally closed (NC) analog switch. |
| MAX5187BEEG | MaximIC | 8-bit, 40MHz, current/voltage-output DAC. |
| MAX6313UK48D4-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 4.680(min) 4.920(max).Nominal timeout period 1120ms. |
