| Parte No | Fabricante | Aplicación |
|---|
| MAX6318MHUK30BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX820LESE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 4.62V. Reset and low-line threshold accuracy +-2% |
| MAX188BEWP | MaximIC | Low-power, 8-channel, serial 12-bit ADC. |
| ICM7218BI/D | MaximIC | 8 digit LED display driver |
| MAX6318LHUK33BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.300V min, reset timeout 20ms, typ watchdog timeout 102ms |
| MAX6320PUK44AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX1242BCSA | MaximIC | +2.7V to +5.25V, low-power, 10-bit serial ADCs in SO-8. INL (LSB) +1 |
| MAX5104EEE | MaximIC | Low-power, dual, voltage-output, 12-bit DAC with serial interface. INL (LSB) +-4 |
| MAX127ACNG | MaximIC | Multirange, +5V, 12-bit DAS with 2-wire serial interface. INL(LSB) +1/2,-1/2 |
| MAX6335US22D1-T | MaximIC | Ultra-low-voltage, low power microprocessor circuit with manual reset (reset output active-high, push/pull . Reset threshold(typ) 2.2V, reset timeout(min) 1ms. |
| MAX780CCNG | MaximIC | Dual-slot PCMCIA analog power controller.Reference & Vpp status indicator. Dual Vpp switches & level shifter for Vcc switching. |
| MX7542KN | MaximIC | CMOS microprocessor-compatible 12 bit DAC. Error +1/2 LSB. |
| MAX1649EPA | MaximIC | 5V or adjustable, high-efficiency, low-dropout, step-down DC-DC controller |
| MAX6316MUK28CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX3222EEPN | MaximIC | +-15kV ESD-protected, down to 10nA, 3.0V to5.5V, up to 1Mbps, true RS-232 transceiver. |
| MAX6317HUK42CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.200V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX166DMJP | MaximIC | CMOS microprocessor-compatible, 5 microsec, 8-bit ADC. Error +-1 LSB. |
| MAX6315US29D2-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 2.93V. Reset timeout period(min) 20ms. |
| MAX354MJE | MaximIC | Fault-protected analog multiplexer |
| MAX4174ACEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 0.5, 1+ (Rf/Dg) noninverting gain 1.5, -3dB BW 1280kHz. |
| MAX161AEWI | MaximIC | CMOS 8-bit 8-channel data acquisition system. Error 1 7/8 LSB |
| MAX734ESA | MaximIC | +12V, 120mA flash memory programming supply. |
| MAX295CWE | MaximIC | 8th-order, lowpass, switched-capacitor filter. |
| MAX232ESE | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX4075BLEUA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 60V/V, noninverting gain 61V/V, -3dB BW 66kHZ. |
| MAX6309UK45D4-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 4.388(min),4.613(max) Nominal timeout period 1120ms. |
| MAX6318MHUK30CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX6321HPUK26CX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX6320PUK39DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX6310UK32D1-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.120(min),3.280(max). Nominal timeout period 1ms. |
