| Parte No | Fabricante | Aplicación |
|---|
| MAX4578EWP | MaximIC | High-voltage, single 8-to-1 cal-multiplexer. |
| MAX6320PUK45AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX4275BBEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 12.5, 1+ (Rf/Dg) noninverting gain 13.5, -3dB BW 460kHz. |
| MAX4077EUA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp/open-loop op amp. |
| MAX4137EWG | MaximIC | 1-input/4-output video distribution amplifier. Fixed gain of 2V/V, 185MHz -3dB bandwidth. |
| MAX1487EEPA | MaximIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 230 microA. Number of transmitter on bus - 128. |
| MAX4051CSE | MaximIC | Low-voltage, CMOS analog multiplexer |
| MAX2442EAI | MaximIC | 900 MHz image-reject receiver. |
| MAX562CWI | MaximIC | Complete 230kbps, 2.7V to 5.25V serial interface for notebook computers. |
| MAX780DEAP | MaximIC | Dual-slot PCMCIA analog power controller. Dual Vpp switches & level shifter for Vcc switching. |
| MAX6317HUK35CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.500V, min reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX6312UK28D4-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 2.730(min) 2.870(max). Nominal timeout period 1120ms. |
| MAX4322EUK-T | MaximIC | Single, low-cost, low-power, Rail-to-Rail I/O op amp. BW 5MHz |
| MAX480ESA | MaximIC | High-precision, low-voltage, micropower op amp. |
| MAX6316LUK42AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.200V, min reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX414BCSD | MaximIC | Quad, 28MHz, low-noise, low-voltage, precision op amp. |
| MAX365EPE | MaximIC | Precision, quad, SPST, normally open (NO) analog switch. |
| MAX307CWI | MaximIC | Precision, dual 8-channel, high-performance, CMOS analog multiplexer |
| MAX6376XR28-T | MaximIC | Ultra-low-power voltage detector, 2.8V |
| MAX4075BJEUA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 49V/V, noninverting gain 50V/V, -3dB BW 50kHZ. |
| DG305BA | MaximIC | CMOS dual and quad analog switch. |
| MAX708TCUA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 3.08V. Active-low and active-high reset output signal. |
| MAX6318MHUK42BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.200V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX9687CJE | MaximIC | Dual, ultra-fast ECL-output comparator |
| MAX6318LHUK46CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.630V min, reset timeout 140ms,typ watchdog timeout 102ms |
| MAX6335US20D2-T | MaximIC | Ultra-low-voltage, low power microprocessor circuit with manual reset (reset output active-high, push/pull . Reset threshold(typ) 2.0V, reset timeout(min) 20ms. |
| MAX542BEPD | MaximIC | +5V,serial-input, voltage-output, 16-bit DAC. INL (LSB) +-2 |
| MAX6321HPUK45BW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 20ms, watchdog timeout(typ) 6.3ms |
| MX574ASQ | MaximIC | Industry standard complete 12-bit A/D converter. 25 microsec. max conversion time. Linearity (LSBs) 1. TEMPCO(ppm/C) 50. |
| MAX6316MUK39BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.900V, min reset timeout 20ms, typ watchdog timeout 25.6secms |
