| Parte No | Fabricante | Aplicación |
|---|
| MAX4690CWE | MaximIC | 1.25om, quad, SPST, CMOS analog switch (two NO switches). |
| ICL7665CSA | MaximIC | Microprocessor voltage monitor with dual overvoltage and undervoltage detection |
| MAX5355EPA | MaximIC | 10-bit voltage-output DAC. +3.3V single supply operation. |
| MAX6316LUK29DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.930V, min reset timeout 1120ms, typ watchdog timeout 25.6sec |
| MX7672BQ03 | MaximIC | High-speed 12-bit A/D converter with external reference input. Fast conversion time 3 microsec. Linearity +-1 LSB. |
| MAX6317HUK31BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 20ms, typ watchdog timeout 102ms |
| REF01Z | MaximIC | +10V precisioon voltage reference. Max TEMPCO 25ppm/degC. Initial error +-50mV |
| ICL7632BCJE | MaximIC | Triple operational amplifier, 5mV |
| MAX4521C/D | MaximIC | Quad, low-voltage, SPST analog switch. |
| MAX382EPN | MaximIC | Low-voltage, 8-channel multiplexer with latchable inputs. |
| MAX3486EPA | MaximIC | 3.3V-powered, 10Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 2.5Mbps. Supply voltage 3.0V to 3.6V |
| MAX5120BEEE | MaximIC | +5V, 12-bit, serial voltage-output DAC with internal reference. INL (LSB) +-1. Single-Supply operation +5V. Full-scale output range +4.095. |
| MAX240C/D | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX4554CSE | MaximIC | Force-sense switches (two force switches, two sence switces and two guard switches configured as two 3PST NO switches). |
| MAX6320PUK30AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec |
| MAX3490CPA | MaximIC | 3.3V-powered, 10Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 10Mbps. Supply voltage 3.0V to 3.6V |
| MAX473CUA | MaximIC | Single, 10MHz single-supply op amp. |
| MAX244C/D | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX6321HPUK49CX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX6318LHUK37CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.700V min, reset timeout 140ms,typ watchdog timeout 102ms |
| MF10BJ | MaximIC | Dual universal switched capacitor filter. |
| MAX1450CAP | MaximIC | Low-cost, 1%-accurate signal conditioner for piezoresistive sensors. |
| MX574AK/D | MaximIC | Industry standard complete 12-bit A/D converter. 25 microsec. max conversion time. Linearity (LSBs) 1/2. |
| MAX6317HUK39DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.900V, min reset timeout 1.12sec, typ watchdog timeout 102ms |
| MAX6318MHUK42DY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.200V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| OP07AZ | MaximIC | Low offset voltage operational amplifier. |
| MAX351CPE | MaximIC | Precision, quad, SPST analog switch |
| MX7533KN | MaximIC | CMOS low-cost 10 bit multiplying D/A converter. Error 0.1% |
| MAX6318MHUK45BY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX6318LHUK41DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.100V min, reset timeout 1.12sec,typ watchdog timeout 25.6sec |
