| Parte No | Fabricante | Aplicación |
|---|
| MAX6337US17D3-T | MaximIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, open-drain) . Reset threshold(typ) 1.7V, reset timeout(min) 100ms. |
| MAX6318MHUK38BY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.800V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX6316MUK46DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.630V, min reset timeout 1120ms, typ watchdog timeout 102ms |
| ICL7614ACPA | MaximIC | Single operational amplifier, 2mV |
| MAX704EPA | MaximIC | Low-cost microprocessor supervisory circuit with battery backup. Precison supply-voltage monitor 4.40V. |
| MAX5150BCEE | MaximIC | Low-power, dual, 13-bit voltage-output DAC with serial interface. +5V single-supply operation. INL(LSB) +-1. |
| MAX130C/D | MaximIC | 3 1/2 Digit A/D converter with bandgap reference |
| MAX6316MUK38BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.800V, min reset timeout 20ms, typ watchdog timeout 102ms |
| MAX199AENI | MaximIC | Multi-range (+-4V, +-2V, +4V, +2V), +5V supply, 12-bit DAS with 8+4 bus interface |
| MAX3245EWI | MaximIC | 1microA supply current, 1Mbps, 3.0V to 5.5V, RS-232 transceiver with autoshutdown plus |
| MAX4275AEEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 1.25, 1+ (Rf/Dg) noninverting gain 2.25, -3dB BW 450kHz. |
| MAX4131C/D | MaximIC | Single, wide-bandwidth, low-power, +2.7V to +6.5V single-supply operation, Rail-to-Rail I/O op amp. 25microA shutdown function. |
| MAX4600CPE | MaximIC | 1.25om, dual SPST, CMOS analog switch. One NC (normally closed) and one NO (normally open) switch. |
| MAX630CSA | MaximIC | CMOS micropower step-up switching regulator |
| MAX780CCAG | MaximIC | Dual-slot PCMCIA analog power controller.Reference & Vpp status indicator. Dual Vpp switches & level shifter for Vcc switching. |
| DG302BK | MaximIC | Dual, TTL compatible CMOS analog switch. |
| MAX4616CPD | MaximIC | Low-woltage, high-speed, quad, SPST, CMOS analog switch has two NC and two NO switches. |
| MX7542GTQ | MaximIC | CMOS microprocessor-compatible 12 bit DAC. Error +1/2 LSB. |
| MAX681EPD | MaximIC | +5V to +-10V voltage converter |
| MAX983CUA | MaximIC | Ultra-low-power, open-drain, dual comparator. Internal precision reference 2%. Internal hysteresis yes. |
| MXD1000PA125 | MaximIC | 5-tap silicon delay line |
| MAX4535CPD | MaximIC | Fault-protected, high-voltage, dual 2-to-1 multiplexer operated with +-4.5V to +-20V dual supply or a +9V to +39V single supply. |
| ICL7652BCPD | MaximIC | Chopper-stabilized operational amplifier |
| MAX6318MHUK35DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.500V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX6322HPUK30C-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 140ms |
| MAX4530EAP | MaximIC | Low-voltage, CMOS analog ICs configured as an 8-channel multiplexer. |
| MAX3386ECUP | MaximIC | 3.0V, +-15kV ESD-protected RS-232 transceiver for PDAs and cell phohes. |
| MAX275ACPP | MaximIC | 4th-order continuous-time active filter |
| MAX6336US17D3-T | MaximIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, push/pull . Reset threshold(typ) 1.7V, reset timeout(min) 100ms. |
| MAX6307UK35D4-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds3.413(min),3.588(max).Nominal timeout period 1120ms. |
